Researchers at Southern University of Science and Technology have created a system for switching between quantum states using mixtures of dysprosium isotopes. The team time-multiplexes 421-nanometer light to selectively slow specific isotopes, generating slow-atom fluxes while simultaneously cooling and trapping atoms with spectrally engineered 626-nanometer light along a common path. This approach allows for the preparation of seven Bose-Bose, Bose-Fermi and Fermi-Fermi combinations, enabling the exploration of multicomponent dipolar quantum matter while maintaining preparation simplicity. The results make isotope composition and quantum statistics selectable within a strongly dipolar system.
Dysprosium Isotope Selection via Time-Multiplexed 421-nm Light
Spectrally engineered 626-nanometer light simultaneously cools and traps dysprosium atoms alongside a novel isotope selection technique, maintaining a common optical path for increased efficiency. This approach allows for the creation of both bosonic and fermionic mixtures using a single optical setup, a counterintuitive feat given the differing quantum behaviors of these particle types. The system’s core innovation lies in the time-multiplexing of 421-nanometer light, enabling precise control over which dysprosium isotopes experience slowed atomic motion, a level of specificity previously unavailable.
The experimental sequence relies on alternating the 421-nanometer light between selected isotopes with programmable dwell times, while the 626-nanometer light addresses both components simultaneously during magneto-optic trap (MOT) loading. This dual-isotope configuration is then sustained through a compressed MOT stage before transfer to an optical dipole trap. Researchers designed the experiment to preserve the simplicity of existing single-isotope dysprosium apparatuses, adding programmable isotope selectivity through optical frequency control.
The ability to adjust the relative dwell time for each isotope during MOT loading provides additional control over the final mixture composition within each one-second switching cycle. Beyond preparation, the time-multiplexed 421-nanometer system also facilitates component-resolved detection. By tuning the probe light to a single isotope resonance while detuning the other by the isotope shift, exceeding the transition linewidth, researchers achieve low-crosstalk imaging of the selected component.
This integrated approach streamlines the process of creating and analyzing these complex quantum mixtures. The resulting mixtures, spanning Bose-Bose, Bose-Fermi and Fermi-Fermi combinations, offer a versatile platform for exploring multicomponent dipolar quantum gases and the many-body phenomena they exhibit.
Spectrally Engineered 626-nm Light for Cooling and Trapping
Spectrally engineered 626-nanometer light enables simultaneous cooling and trapping of dysprosium atoms along a shared optical path, a design element that helps maintain efficiency in the creation of quantum mixtures. This approach bypasses the need for separate systems for bosonic and fermionic preparations, using a single optical layout for both, a feat previously challenging in ultracold atom experiments. The 626-nm light’s generation relies on sum-frequency generation of 1550-nm and 1050-nm seed lights, with isotope-resolved spectral programming imprinted onto the 1550-nm seed using a fiber Mach-Zehnder electro-optic modulator.
This allows for precise control over the light’s interaction with different dysprosium isotopes. The system’s ability to create mixtures of bosonic and fermionic isotopes stems from a time-multiplexed 421-nanometer light source, generating isotope-selective slow-atom fluxes, and the spectrally engineered 626-nm light.
The 626-nm light’s spectral engineering is particularly important for fermionic isotopes, where it is tuned to address the F = 21/2 → F′ = 23/2 cycling transition. While the 421-nm transition can couple to nearby hyperfine transitions due to its broader linewidth, the 626-nm transition offers more spectrally selective addressing. This precision is maintained through the compressed MOT stage, where the 421-nm beams are switched off and the 626-nm MOT spectrum is adjusted for further cooling and compression. Detailing the fine-grained control over mixture composition is important for understanding the experimental process.
Preparation of Bose-Bose, Bose-Fermi, and Fermi-Fermi Mixtures
The ability to finely control the composition of quantum mixtures is now significantly advanced through a new system capable of preparing seven dysprosium isotope pairs, spanning Bose-Bose, Bose-Fermi and Fermi-Fermi combinations. This preparation maintains flexible isotope-pair selection and tunable population balance, a level of control achieved while retaining the simplicity of a single-isotope experimental setup. Researchers evaluated performance by introducing a hierarchy of sequence-matched single-isotope controls, assessing effects from dual-frequency operation to full dual-isotope preparation, extending from magneto-optical-trap loading and compression to optical-dipole-trap transfer.
This system accesses a broad compositional range, creating samples strongly enriched in either dysprosium-162 or dysprosium-164 while keeping the optical configuration and preparation sequence constant. Near-balanced populations of the 162Dy-164Dy mixture are obtained using comparable dwell times, decoupling the prepared mixture composition from the natural abundance ratio and enabling programmable population imbalance.
This timing-based control provides a practical method for producing isotope mixtures with precisely tailored compositions, a feature that supports exploring many-body phenomena. Comparisons reveal near-unity ratios indicating dual-isotope operation introduces little additional reduction in maximum transfer efficiency relative to single-isotope references. Systematic benchmarks demonstrate that most preparation components retain nearly single-isotope-like performance throughout the sequence, with appreciable deviations limited to specific isotope combinations and stages.
Observed loading degradation is predominantly associated with the optical preparation, rather than a generic instability of the isotope mixtures, as revealed through controlled measurements. “These controls separate the common technical cost of time-multiplexed loading from pair–specific optical sensitivities,” the study reports, highlighting the system’s robustness. The work establishes a reconfigurable platform for exploring multicomponent dipolar quantum matter.
Optical Frequency Reconfiguration for Isotope Mixture Control
The same optical system facilitates isotope-selective broad-line cooling, programmable flux control and component-resolved detection, a level of integration achieved through frequency agility at 421 nanometers. This is accomplished by switching between isotope resonances during imaging, detuning the probe light from one isotope while simultaneously targeting the other, exceeding transition linewidths to minimize crosstalk.
Beyond imaging, the 421-nanometer light sequence governs mixture composition by controlling the relative dwell time allocated to each isotope during magneto-optical trap (MOT) loading, offering a precise method for tailoring the final isotope ratio. This time-multiplexed approach allows for the creation of dysprosium mixtures spanning a broad compositional range, from samples heavily enriched in one isotope to those with near-balanced populations.
A carrier-suppressed double-sideband (CS-DSB) regime is employed with the 626-nanometer modulation, concentrating optical power into the targeted first-order sidebands and suppressing unwanted frequencies. This modulation frequency is set to half the separation between the 626-nanometer MOT transitions, accounting for hyperfine shifts in fermionic isotopes, ensuring efficient addressing of both isotopes simultaneously. The resulting configuration favors strong spatial overlap between the addressed isotopes, as both experience closely matched optical trapping geometries within the same beam paths.
This allows for simultaneous dual-isotope MOT and CMOT operation without the need for additional isotope-specific cooling beams, streamlining the experimental setup. The system’s ability to maintain this control throughout the preparation sequence is key to exploring many-body phenomena in these unique quantum mixtures.
Single-Isotope Performance Benchmarks for Mixture Preparation
Systematic evaluations of the preparation process reveal near single-isotope performance for most dysprosium combinations, a key factor in streamlining experimental workflows for multicomponent quantum systems. These benchmarks move beyond simply achieving mixtures, focusing instead on maintaining the efficiency of single-isotope preparation methods when creating these combined states.
Absolute efficiencies characterize the performance of the common preparation sequence, rather than optimized transfer efficiencies for individual isotope pairs. The loading ratio was used to evaluate changes introduced by dual-isotope operation. For the majority of isotope combinations tested, this ratio remained close to unity, indicating that the number of atoms obtained in the dual-isotope mixture closely matched that of interrupted single-isotope references, even with the addition of the second isotope and its associated 421-nanometer addressing.
The ability to establish a reconfigurable preparation scheme for both bosonic and fermionic dysprosium isotope mixtures while retaining a single-isotope experimental setup is a significant achievement, extending across Bose-Bose, Bose-Fermi and Fermi-Fermi combinations. “These absolute numbers therefore characterize the accessible sample sizes under comparable dwell-time allocation rather than providing a direct comparison of intrinsic preparation performance between different isotope pairs,” the researchers write, emphasizing the focus on maintaining consistency across different mixtures. The three-letter labels, specifying 626-nanometer spectrum, 421-nanometer operation and the atomic sample, provide a detailed framework for assessing performance changes at each stage of the process, ensuring a rigorous evaluation of the preparation technique.
Magneto-Optical Trap Loading and Compression Comparisons
This approach minimizes optical losses as the system transitions between preparing different quantum mixtures, a key challenge in dipolar quantum matter research. The experimental sequence mirrors single-isotope preparation, with dual-isotope operation achieved primarily through time-multiplexed switching of 421-nanometer light and spectral engineering of the 626-nanometer MOT light. During magneto-optical trap loading, the 421-nanometer light provides both transverse cooling and Zeeman slowing, while being time-multiplexed between the two isotopes being combined.
These controlled comparisons reveal how effectively the system maintains performance across different preparation stages, and for different isotope pairings. The optical dipole trap is activated during compression, before the atomic cloud reaches the trapping region, ensuring spatial overlap as the compression sequence progresses. The overall experimental sequence retains the same structure as the single-isotope preparation, according to supplemental material detailing the experimental setup, emphasizing the design’s efficiency.
Optical-Dipole-Trap Transfer of Dysprosium Isotope Mixtures
The system’s design prioritizes maintaining the simplicity of single-isotope dysprosium apparatuses while introducing programmable isotope selectivity via optical frequency control. To rigorously assess this reconfigurable platform, researchers established a hierarchy of sequence-matched single-isotope controls, isolating the effects of dual-frequency 626-nanometer operation, interrupted 421-nanometer cooling, and complete dual-isotope preparation. These systematic comparisons extended from magneto-optical trap (MOT) loading and compression stages through to optical-dipole-trap transfer, revealing performance levels comparable to single-isotope preparations for most combinations. Measurements of MOT lifetimes for both dual-isotope mixtures and corresponding single-isotope references, conducted under near population-balanced conditions, indicate minimal performance degradation.
Pair-Dependent Optical Sensitivities and Density Losses
Controlled measurements reveal that deviations from single-isotope performance are not uniform across all combinations of dysprosium, manifesting as pair-dependent optical sensitivities during the loading stage and additional density-related losses. While the initial magneto-optical trap (MOT) exhibits minimal additional loss when operating with dual-isotope mixtures, enhanced decay emerges for specific combinations as the density increases within the compressed MOT (CMOT). These component-dependent differences also become apparent during the transfer of atoms into an optical dipole trap (ODT), indicating that certain stages require further optimization for achieving quantum degeneracy with diverse isotope pairings.
👉 More information
🗞 Reconfigurable Dysprosium Isotope Mixtures with Selectable Quantum Statistics
✍️ Zibin Jiang, Kaiyue Wang, Shenshuang Nie, Junrong Huang, Fucheng Qin and Mingyang Guo (Department of Physics and Guangdong Basic Research Center of Excellence for Quantum Science, Southern University of Science and Technology, Shenzhen, China)
🧠 ArXiv: https://arxiv.org/abs/2611.21028




See today’s quantum computing news on Quantum Zeitgeist for the latest breakthroughs in qubits, hardware, algorithms, and industry deals.
